Canon 1D mark III teardown

What is worse than having a leak in the roof of your house? -Leaving your super expensive Canon camera right under it.

Yes.

After one night of “Chinese water torture”, my camera gave up and didn’t power on any more, even after some drying on a heating.

It was actually three months ago, but I only had the time/need to do something about that just now (and of course, the warranty expired two months before it happened).

As I didn’t have much to loose, I decided to give a try and to fix it myself.

The quality of the photos should be better, but I didn’t really have the time or the motivation for that. Sorry. I took a lot of them when I was actually re-assembling the camera, so it’s not a *real* teardown (I was really desperate of the camera not working any more)

The basic tools are a set of philips screwdrivers and some boxes to put the screws (there are different lengths/threads). Tweezers and a plastic spudger can help. I also used electrostatic protective wrist band and electrostatic mat.

01-Canon-1D-Mark-III-Teardown

02-Canon-1D-Mark-III-Teardown-Stripped-Front

To access any screw, you need to undress the camera first by pulling off the pieces of rubber (I don’t know if it’s the glue used or my extreme way of using my cameras, but they were easy to peel).

The rubber on the memory card door doesn’t actually need to be removed. No screw there.

All the screws need to be removed and sorted.

This small piece of copper looks like a capacitive hand presence detector (there’s an other one on the other side of the grip) but it’s  not, as it isn’t connected to anything. If anyone knows what its purpose is, don’t hesitate to comment.

Once all the visible screws are unscrewed, it’s possible to remove the back panel with the LCD screen. It’s connected to the mainboard by two flat flexes and two sets of cables. Unfortunately, I didn’t take a picture of it.

A view from the back of the guts

Not-so-easy-to-spot-screw, holding the front assembly.

At first, I wondered what the two holes on the bottom were for..

This last screw is holding the top assembly. Tricky to spot, especially if you don’t remove the front cover..

More flex cables!!

The power management board. Note how some of the chips pins are coated. The black/red cable on the left comes from the battery DC/DC converter (a small PCB on the top of the battery compartment). As you can see, there are several SMD fuses on the board. Unfortunately, all of them were good.

Removing the power mngt board reveals one of the memory cards slot

Water is good for humans, not for $4000 cameras.

And the other side is affected too. The small board on the bottom is the battery DC/DC converter.

Caution! The next photo is really graphic. Don’t click to see it full size.

You never listen…

That’s also a good reason why it’s important to clean/dry any electronics that were in contact with water immediately. “Do what I say, not what I do”

After cleaning. Already better. There’s still some hope.

Nope. The hope is gone.

Let’s put it back and see what happens.

Next water damaged part: the top LCD and its buttons.

Ok, this one isn’t as horrible as the rotten PCB.

The top LCD assembly with the backlight, exposure correction and ISO buttons.

Backlighting/LCD display sandwich, held pressed together by the metallic piece laying on the right and two screws. There’s foam around the LCD to prevent condensation between it and the sealed transparent plexiglas.

Water was here. Come on Canon, stainless steel?

 

After more cleaning and re-screwing all the screws in the right order, I tried to power up the camera again. This time, it worked!

Unfortunately, the top LCD isn’t working. Luckily, all its information can be displayed on the main screen (“00” because no lens attached):

Also, more annoying, all the info in the viewfinder are gone. The AF system, AF points selection and all the rest seem to work as good as new (ok, as before the water damage). I’m not doing sport photography any more, so I should be able to use the camera like that and wait till I have enough money to send it to service or to buy a new one.

Advertisements

10 thoughts on “Canon 1D mark III teardown

  1. Pingback: La petite boutiques des horreurs

  2. Hello! You did a really cool job with this camera. I have the same problem with a Canon 1d mark ii N. I took it apart but I’m not quite sure what to use for the cleaning part of the process. People suggested alcohol. Did you use a special kind of cleaning product ?

  3. I dropped my Mark III and now it won’t power on. No visible damage. In looking it over there are 2 battery contact pins that are longer than the rest. Is that they way it’s supposed to be?

    How do I check the fuses? Thanks!

    • I checked on my camera and yes, the two outer pins are longer. I’d suggest sending your camera to Canon, but if you can and really want to do it yourself, you could start wit trying an other battery (or the DC power dummy battery, if you have it). Before checking the fuses (with a multimeter), I’d check the connectors inside first.

  4. Hello, I will need frame to repair the 1DS MKiii one of my friend. I dont know if it’s the same frame but if you have frame parts, let me know I may buy it from you.

  5. Hello, I need replace the usb conection.Do you remember if to change it is possible remove the front and rear covers only or I also need remove the top cover?

    Thanks a lot for your work

  6. hi, but where is the main board? on the right sd slot of the camera?
    in this days i try to disassemby my 1D mk3

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s